Sale of pumps: | sbyt@hms-livgidromash.ru |
Reception: |
lgm@hms-livgidromash.ru |
Control & Protection Station (hereinafter referred as to the C&PS) «HMS Control L4» is designed to control and protect three-phase induction electric motors provided with squirrel-cage rotor, of foreign manufacture or domestically made; functionality is ensured by operator command or by sensor signal and it is suited to the requirements of Technical Specifications: 3432-112-00217975-2011.
C&PS "HMS Control L4" ensures the following design conditions:
C&PS corresponds to climatic version U2 or UXL4 as per GOST15150-69. (U2 – denotes operation in unheated premises or under the shed at a temperature of ambient air from minus 40 up to plus 40°С and relative humidity 100% at 25°С, UXL4 version – denotes operation in enclosed heated premises at a temperature of ambient air from plus 1 up to plus 40°С and relative humidity 80% at 25°С).
Level of protection of the C&PS against water and dust - IP 54 as per GOST 14254-96.
As far as the protecting people against electrical shock is concerned, C&PS is reffered to the 1st class, GOST 12.2.007.0 -75.
Control & Protection Station (C&PS) consists of the control board fitted with removable assembling panel, within which provision is made for automatic circuit breaker, electromagnetic starter, softstarter (depending on the version), electromagnetic relays (depending on the version), terminal blocks (power blocks and signal blocks) and current sensors (current transformers).
Arranged on the door of the control board is a microcontrolling device for control and protection -“L4" (hereinafter referred as to the MC).
Depending on the version, the station may include a switch-disconnector at the in-feeding port, monitor module for controlling the temperature of bearings of the motor and/or pump, protection module against impulse overvoltage (lighting protection) and GSM-modem of different modifications.
Arranged on the front panel of the MC (microcontroller) are the control buttons, namely: «START», «STOP», «OK», «ESC», navigation buttons, graphic LCD indicator and light-emitting diodes (LED) to indicate modes of operation and emergency conditions.
Arranged on the rear panel of MC casing are split-design terminals used to connect to the external electric power circuits and sensors.
The principle of operation of C&PS is based on processing the signals coming from external sources to the MC (microcontroller) and on operating the softstarter or the starter switching in/off the electric motor.
Provision is made for two modes of operation: manual operation, when the startup/stoppage of the motor is carried out by pressing buttons “START”/“STOP”, or automatic operation, when the startup/stoppage of the electric motor is carried out via the signal (s) from the level (pressure) sensor (s) or by the commands from APCS (Automatic Process Control System).
Options | Values |
Series | HMS Control L4 |
Weight, kg | 86 |
For example HMS Control L4-25-P-M-IP54-UXL4 , where :
Denomination |
Parameter |
Rated supply voltage, V /current frequency, Hz |
~380/50 |
Quantity of in-feeds, pcs. |
1 |
Permissible deviation of the supply voltage fr om the rated value, % |
+10
|
Maximum current of the electric motor to be connected up, А
|
300 |
Range of temperature during operation, °С |
+1…+40 (-40…+40 for U2) |
Degree of protection of enclosure as per GOST 14254-80 |
IP54 |
Normal power feeder, inputs for electric motor and sensors |
in the bottom portion of the cabinet |
Kind of climatic version |
UXL4 (У2) |
Denomination of the input signal |
Kind of signal |
Sensor of “dry” running 1 |
= 24V |
Sensor of “dry” running 2 | |
Sensor of lower level | |
Sensor of upper level | |
Sensor (line loop) of the burglar alarm | |
«External» control | |
«External» error | |
Signal «Automatic mode of operation» | |
Analog pressure/level sensors |
4…20 (0…20) mА |
Temperature sensor (Pt100, RTS, thermocontact) |
0…3,5 кOhm |
Current sensor 1…3 |
0…5 А |
RS-485 |
= 5V |
RS-232 |
= 12V |
Denomination of the output signal |
Characteristcs |
Operating trouble (emergencies) |
НО/НЗ relay contacts
|
Custom event (to be adjusted by the User)
|
Manual mode of operation is intended for local control of the motor in the course of assembly and service activities. The proper motor switching in/off is effected by depressing the buttons «Start»/«Stop», arranged on the frontal panel of the MC. Transition to the manual mode of operation takes place when the flag indicator SB1 is moved into the position «Manual».
With the unit being operated manually, all the protective gears (protections) are actuated but with the exception for control of correct operation of the level indicators and limitation on number of motor starts per an hour. When the protective gear is actuated the motor is to switch off and the blinking inscription about emergency situation together with the sound signal is displayed before the operator intervention.
Time timers of duration of work and the switch on/ switch off time timers are not used.
Remote motor control via communications lines or sms-messages is blocked.
Under automatic operation conditions the pump motor is automatically switched on/off according to the discrete or analog pressure/level sensors. Depending on the station function that is to be chosen by the User it is possible to maintain automatically the water level in the reservoir or to drain the drainage pits.
«Filling» Control Function
When the liquid column is lowered below the low-level indicator, the supply mains and motor are checked for condition and the signal of the sensors is verified for correctness. Thereupon the actuation of the pump motor takes place. In the course of filling process the control of currents and voltages is constantly carried out, those values are to be within the set limits. If the current and voltage values go beyond the target values' range during the prescribed time period, the electric motor is subject to emergency shutdown. In such a case the indicator will display the code of the offered error and the time up to the next following launch of the motor. Additionally in the course of operation the status of the input “External control” and the condition of the “dry” run sensor are to be verified. When the reservoir is filled up till the upper level, the motor is switched off and the MC (microcontroller) is moved to the drainage waiting mode.
Under automatic operation conditions the status of the level gauges' contacts is always controlled..
As the problem connected with wrong functioning of the sensor contacts appears (for example, the high-level indicator is actuated prior to the low-level indicator), the level LEDs start flashing and in 2 minutes the protective gear is activated. The motor is switched off and the blinking emergency code is displayed. The error is cleared just after regeneration of signals coming from the sensors (indicators).
Some additional functions are available during automatic operation, namely: emergency shutdown timer and on and off delay-make timer.
The emergency shutdown timer is designed to exclude the overfilling due to fault of one of the level gauges (for example, the high-level indicators at the water tower are frequently frozen). The task of the timer – to de-energize the motor on expiration of time period prescribed in the setup menu (in minutes), if the high-level indicator did not come into action. The timer is initiated together with the motor actuation during filling process and it is reset to zero when the motor is switched off. If the level gauge operates prior to the timer (with respect to time), so the timer is stopped up to the next following motor activation. After timer-clock response and on expiration of restart time after emergencies, the operation of the station is to be continued as per normal, the Microcontroller looks forward to lowering of the liquid level.
On & Off delay-make timers make it possible to ignore false level signals under possible water hammer effects on the long lines, which are involved just after motor switching in/off. The start-up command or the stop command of the motor will be executed only after stabilization of the pressure jump and stable condition of the sensor contacts during time period predetermined by the User. In addition, one should use delay timers in order to organize the group (cascade) mode of operation for several pumps just to suit one storage tank or drainage tank with common level gauges. Switch on/ switch off time of every station from the group is adjusted in dependence to operation conditions for a time period up to 180 seconds.
«Drainage» Control Function
Operation of the station under drainage conditions is identical to operation under filling-up conditions with the exception of reverse sequence of motor switching in/off when the liquid level is changed. When the liquid comes up to the upper level, the motor is just actuated. When the minimum level has been reached, the motor is stopped, in such a case the station will be looking forward to filling-up of the reservoir up to the upper level. Similar to above-mentioned filling-up function, it is possible to use the following functions, namely: switch on/switch off delay and emergency shutdown function as well.
As far as the “drainage” control function is considered, bear in mind that the launch time delay and the shutdown delay functions are in analogy with the station function of “filling process”, but the timer of emergency shutdown is activated jointly with the motor and is cleared when the lower level is reached.
The said mode of operation is provided for such conditions when the installation of the high-level sensor (indicator) is not really possible (for example, the high-level sensors which are used at the water towers are to be covered with ice during hard frosts and as a result they become non-operative), and the electric-contact manometer has difficulty in use for some reason. In this case only one level indicator is to be installed; after its triggering the filling-up/drainage of the reservoir is effected during time lim it required for the purpose of filling and draining. The high-level sensor (indicator) is not used during automatic mode of operation. The filling function or drainage function is to be chosen in the setup menu of the microcontroller (MC). In the course of filling-up process the good use is made of the low-level sensor input, during drainage – the input of high-level sensor is brought into operation.
In the process of filling
If the sensor is found in open position, it means that the liquid is not present in the reservoir, so the pump motor starts working for a time ranging from 1 up to 180 minutes (time to be changed by the User in the setup menu). The time for filling a specific tank is selected by way of trials in hand-operated regime. When the time of filling is expired the MC will look forward to opening operation of the low-level indicator and then it will repeat over again the cycles of filling.
In the process of drainage
If the sensor is in closed condition, it means that reservoir has been filled up, so the motor starts working for a time ranging from 1 up to 180 minutes. Time required for draining the certain reservoir is chosen manually by trial. When the time of bleeding (draining) is expired, the MC will look forward to closing operation of the low-level sensor, иand then it will repeat over again the cycles of drainage.
As in all other modes of operation, the check-up of all applied protective parameters is carried out just before the start and in the course of the electric motor operation.
Remote control is possible with the help of the input “External control” of the station. The said input must be enabled in the setup menu of the MC. Under automatic operation conditions the closure of the said input admits operation of the station in this mode of functioning, the opening (breaking) of the said input – forbids the operation. The motor is to be switched on just while the level gauges will operate with positive action in accordance with applied duty cycle and function. Restart after emergency condition will take place after the expiry of the prescribed hold-up time.
During manual operation at closing of the input, the electric motor is energized immediately, at opening of the input – it is de-energized. After actuation of the protective gear the motor is to be switched off and the blinking code of emergency will be kept on the indicator. The alarm clearance and restart in case of enabled input «External control» - the opening of the said input or the depressing the «Stop» button of the MC. The emergency condition will be cleared and, in dependence to input status, the motor will be switched in/off.
In the time of activated «External control” input, the buttons «Start» and «Stop» of the Microcontroller will be blocked.
The said operation is provided to control remotely the motor via the wirelines or wireless communication links. L4 is furnished with physical interfaces RS-485 and RS-232, by which it is possible control remotely and to monitor all the parameters of the Microcontroller. The specific port is chosen by the User in the setup menu. The communication ptotocol with remote PC or PLC - ModbusRTU. The transmit speed of 2400...57600 bit/sec., the length of communication line (tie line) – up to 1 km. (suits for RS-485). In case of longer communication lines it is necessary to use the repeaters or radio modems.
Under such mode of operation the managing program (supervisory program) for PC (PLC) or the User read the L4 sensors' status or the decision about switching in/off the motor is made at own discretion. The motor is switched in/off by writing “1” or “0” into the zero bit of the register “Control”. The working status of the sensor (s) of “dry” run is constantly checked just after the supply power-on with no regard to the mode of operation. The duty of the station (filling or drainage) and the type of the level gauges does not have an effect on motor operation, their condition is printed on the screen. The switch in (switch off) delay-make timers and emergency shutdown timers are not used under given working conditions. When the protective gear operates with positive action the motor is switched off and the error message is screened on the indicator. The error is automatically reset just after the expiry of hold-up time or after having performed the forced clearance from the PC (PLC). Under such operation conditions the User controls the general-purpose relays 1 and 2 (K2 and К3) by way of the remote PC or PLC. Their functions, chosen in the setup menu, ARE TRIPPED OFF! The relay is switched in/off by writing the 1(0) value into the corresponding bites of the Register “Control”, described in the document “L4. Protocol specification Modbus RTU”.
If the wirelines are not available, the monitoring and control over the station may be effected with the aid of radio and GSM-modems. The modems may be connected to not only to interface RS-485, but also to RS-232(to be adjusted in the setup menu L4).
The both GSM-modems (one modem within the control box of HMS Control L4, but the second – in CPCS (Computerized Process Control System) are automatically interconnected and exchange data via the Protocol Modbus RTU. In case of radio modems it is necessary to adjust the communications parameters of both modems only, for the case with GSM-modems the sim-card of the station modem must be provided with constant (static) IP-address and data communication function (to be provided by the cellular communication operator). With supply power-on the GSM-modem of the station is Online registered with constant address, and expects for requests from the CPCS modem. The CPCS of the User with the help of the second GSM-modem transmits requests to pre-existing IP-address of the station modem and receives data from the latter.
It is possible to switch in/off the motor by way of commands from the sms-messages.
The operating principle: the User sends the sms from the cellular telephone to the number of the GSM-modem with certain control command. The GSM-modem receives the said message and transmits it to the L4, the latter is to analyze the message and to start/stop the pump motor. During processing of the command the number of the phone with whom the above-mentioned message was sent is verified without fail. If the number of the phone does not coincide with the number prescribed in the L4 setup menu, the said message will be ignored. It is done in order to exclude attempts of unauthorized control of L4 from another phone numbers.
Supposedly, the following working situations might be expected when in connection with equipment failures or because of the unstable operation of the cellular network the User can run out of control over operation of the pump, and as a result of which, for example, the overflow of the reservoir and the flooding of the premises or working site will take place. To exclude such cases and situations the L4 has provision for emergency shutdown of the pump motor within the target time to be preset by the User. Besides, at the moment of receiving the message provided with the command, the proper time of message delivery is to be verified. In consequence of possible faults (upset conditions) or due to great workload of the cellular communication operator, the message with the control command may be delivered with great. In order to exclude undesirable startup/stoppage of the motor in such cases, during processing of the accepted message the L4 is to check the delivery time of the said message. If the time-delay is more than 15 minutes the given command is ignored, and the reply message with indication about time-delay will be sent.
For distance transmission of the signals to the dispatcher desk or CPCS (computerized process control system) provision is made in the station for three electromagnetic relay K1-K3 of the controller provided with double-throw contact.
The relay К1 is adjusted to operate with positive action under emergency situation. As for the relay К2-К3 the closure of the relay contacts takes place in dependence to selected condition within special item of the MC setup menu.
Available are the following variants of relay actuation:
In case of necessity, the signal «Switched on/off motor» may be obtained by using additional NО-contact (a-contact) which is accommodated within the electric contactor.
To be more familiar with the operation of the station refer to the documents «L4 Programming Manual», «HMS Control L4 Operation Manual » and «L4. Protocol Specification C Modbus RTU».
|
|
All technical documentation in the Russian version of the site »
All certificates, permits in the Russian version of the site »
© Copyright 1999-2024. All rights reserved. When using materials from the site and permit the direct hyperlink on www.hms-livgidromash.com reserved.